How to Remove and also Change a Bathtub.
How to Remove and also Change a Bathtub.
Blog Article
This post listed below involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is definitely stimulating. Read on and draw your own personal assumptions.
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and often, tiling skills. Replacing an old bath tub with a new one is additionally a moderately challenging task. If the old bathtub is readily easily accessible, the task can move immediately; if you need to open a wall to get rid of the old tub as well as place the brand-new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to leave the old bathtub and set in the new one. Make certain you have actually qualified yourself for the task and also fit attempting it. As opposed to hiring a specialist to take control of a halfway-completed task, it is better to think about employing one before you start. Possibilities are you might require a specialist plumber to make tube connections.
This short article will certainly aid you mount a new bathtub in your restroom if you have currently gotten a brand-new bathtub and also do not need to change the setup of your previous water system pipelines.
Your devices and also product checklist must consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is detach the supply of water. After doing so, switch on the taps to drain any water remaining in the system. The process of removing the existing taps can be quite problematic as a result of the limited gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipes. As soon as the supply pipelines have been removed, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleaned of any old securing substance.
Before carrying on to fit the brand-new taps, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will call for lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in place in between the tap and the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the tap finishes initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Making use of the two wood boards under its feet, position the bathtub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little factors.
The following goal is to make certain that the tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the bath tub till the spirit level checks out degree.
To install faucets, fit all-time low of the outermost flexible faucet connector to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Switch on the water system and inspect all joints and brand-new pipework for leakages and tighten them if required. Load the bath tub and likewise examine the overflow outlet as well as the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been made use of at the very least once as this will resolve it into its final placement.
Planning for the Installation
First of all, the sustaining structure provided with the bathroom should be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its last placement.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, triggering the water to permeate the wall between the bathroom and the tiling, bring about issues with moisture and possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components and also fittings. They are marketed in tubes and also cartridges, and can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to always load the bath tub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealer can break rather very early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that short article was a great idea. Liked our article? Please share it. Help other people find it. I truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Appointment Report this page